Phoenix terminal is a type of equipment used for electrical wiring, its application scope is more and more widely, in use in order to smooth the completion of the work, then we should pay attention to some matters, let's talk about it.

　　擰緊力要適中。避免用力過大來松開螺栓和螺母。如果發現螺栓和螺母有松動，請立即更換，不要湊合工作。用螺絲刀擰緊或松開菲尼克斯端子的螺母時，一定要用螺絲刀用力擰緊螺絲，然后再擰緊或松開，以免螺絲刀與螺絲跑偏，造成螺絲損壞，不易拆卸，特別是在吊箱。普通空氣開關。

　　Tightening force should be moderate. Avoid using too much force to loosen bolts and nuts. If the bolts and nuts are found to be loose, please replace them immediately, do not work at all. When using a screwdriver to tighten or loosen the nut of phoenix terminal, make sure to tighten the screw with a screwdriver and then tighten or loosen the screw. Otherwise, the screw may be damaged and difficult to remove, especially in the hanging box. Common air switch.

　　如發現螺栓、螺母難拆裝，不必魯莽行事，以免變形難拆裝，應提供適度敲擊，或加螺絲松動劑、稀硫酸等拆裝前。不要用虎鉗擰緊或松開螺栓和螺母，以防損壞。使用活動扳手時，應調整開口，以免螺栓、螺母損壞變形，造成拆卸困難。同一個菲尼克斯端子允許連接兩根以上同類型、同規格的電線。

　　If bolts and nuts are found to be difficult to disassemble, there is no need to act rashly to avoid deformation and disassembly. Moderate percussion should be provided, or screw loosening agent and dilute sulfuric acid should be added before disassembly and assembly. Do not tighten or loosen bolts and nuts with a vise to prevent damage. When using an adjustable wrench, adjust the opening to avoid damage and deformation of bolts and nuts, which may cause difficult removal. The same Phoenix terminal can be connected to more than two wires of the same type and specification.

　　對于容易松動或接觸不良的接線端子，必須用“？”將接線器緊固在接線端子上。類型以增加總接觸面積并避免松動。線接頭或線頭相互連接時，禁止修改中間的非銅或低導電性墊片。連接線材連接器時，規定接觸區域清潔，無空氣氧化。接線鼻或銅排連接時，接觸表面后可將導電膏擦拭干凈，然后擰緊。

　　For terminals that are easily loose or in poor contact, use? Fasten the connector to the terminal block. Type to increase the total contact area and avoid loosening. Do not modify the non-copper or low conductivity gasket in the middle of the connector or connector connected to each other. When connecting wire connectors, ensure that the contact area is clean and free from air oxidation. When connecting the wiring nose or copper bar, wipe the conductive paste clean after touching the surface, and then tighten it.

　　連接菲尼克斯端子的臨時線時，應將單線銅線的規定端子對折一次，然后接到空氣開關的下孔；單芯硬線應收在“？”鍵入空氣開關的下孔。30KW及以上電機接線，規定電機組出線與電纜之間不得使用熱鍍鋅螺母、平墊圈、扭簧墊圈等導電性能差的墊圈當用絕緣膠帶纏繞電纜或其他機械設備以保持絕緣層時，電纜護套應按壓力位置的1/2比例從一端到另一端纏繞，至少繞一圈。

　　When connecting the temporary line of Phoenix terminal, the specified terminal of single wire copper wire should be folded in half once, and then connected to the lower hole of air switch; Single core hard wire receivable in "?" Type the lower hole of the air switch. 30 kw and above motor wiring, rules between the electric wire and cable unit shall not be used galvanized nuts, flat washers, torsional spring washers and so on about the worse performance of conductive gaskets when wrapped with insulating tape cable or other mechanical device to keep insulation, cable sheath should press stress position of 1/2 scale from one end to the other side, at least around a circle.

　　好了，以上便是問題的相關解答內容了，希望對您有所幫助吧。那么如果您還有別的問題想要了解的話，歡迎您對點擊http://www.xzthjc.com網址進行咨詢！

　　Well, the above is the relevant answers to the problem content, I hope to help you. So if you have other questions to understand, you are welcome to click on the http://www.xzthjc.com website for consultation!