菲尼克斯端子做為完成保護接地的一種零配件產品，與電氣設備相接，那么要想更好的使用該產品，就要留意很多的事項。下面來講講相關內容吧。

　　Phoenix terminal as a protective grounding of a spare part products, connected with electrical equipment, so in order to better use the product, we must pay attention to a lot of matters. Let's talk about the relevant content.

　　菲尼克斯端子的使用擰緊接線用力要適度，避免用力過將軍螺栓螺母扣松，發覺已扣松的螺栓螺母立即拆換，禁止湊合工作。用螺絲起子擰緊或松脫螺母時，務必用力使螺絲起子頂緊螺釘，隨后再開展擰緊或松脫，避免螺絲起子與螺釘跑偏，導致螺釘損害不容易拆卸。

　　The use of Phoenix terminal to tighten the wiring force should be moderate, avoid excessive force general bolt and nut buckle loose, found loose bolt and nut immediately disassemble, prohibit casual work. When tightening or loosening the nut with a screwdriver, be sure to tighten the screw with the screwdriver, and then tighten or loosen the screw to avoid deviation between the screwdriver and the screw, resulting in screw damage and not easy to remove.

　　發覺難以拆裝的螺栓螺母，不必魯莽行事，避免導致形變更難以拆裝，應提供適度敲擊，或加螺絲松動劑、稀硫酸等稍候再開展拆裝。不能用老虎鉗擰緊或松脫螺栓螺母，防止導致毀壞，用活口扳手時要調節好張口，避免將螺栓螺母毀壞形變，導致不容易拆卸。

　　If you find it difficult to disassemble bolts and nuts, do not act rashly to avoid deformations that are more difficult to disassemble. Moderate percussion should be provided, or screw loosening agent and dilute sulfuric acid should be added to carry out disassembly later. To prevent damage, do not tighten or loosen the bolts and nuts with a vise. When using a adjustable wrench, adjust the opening properly to prevent damage to the bolts and nuts and prevent them from being easily removed.

　　導線連接頭或線鼻子相互之間聯接時，正中間禁止改裝非銅質或導電率能不太好的墊圈。導線連接頭聯接時，規定接觸面積光潔且無空氣氧化狀況，接線鼻部或銅排相連時，可在觸碰表層清洗整潔后擦抹導電膏，隨后再開展擰緊。

　　When connecting wire connector or wire nose to each other, it is forbidden to refit non-copper washers or gaskets with poor conductivity in the middle. When connecting the wire connector, the specified contact area should be smooth and free from air oxidation. When connecting the wiring nose or copper bar, wipe conductive paste after cleaning the contact surface, and then tighten it.

　　接臨時性線時，單條導線銅線的規定接線頭折起來一次，隨后收到空氣開關下孔；單芯硬線要以“？”型收到空氣開關下孔。應用絕緣膠布盤繞電纜線或別的要維護絕緣層的機器設備時，電纜護套應以壓置1/2的占比從一端盤繞到另一-端，且至少來回一往返。

　　When receiving the temporary line, the stipulated wiring head of a single wire copper wire is folded once, and then the hole under the air switch is received; Single core hard line to “?” Receive air switch under hole. Application of insulation tape winding cable or other equipment to maintain the insulation layer, the cable sheath should be pressed with a ratio of 1/2 from one end winding to the other end, and at least one back and forth.

　　菲尼克斯端子的使用要留意不少的事項就是這樣了，當然還有很多注意事項需要大家在使用中多多關注，更多內容就來網站www.xzthjc.com咨詢吧。

　　Phoenix terminal use to pay attention to a lot of matters is this, of course, there are a lot of matters needing attention in use, more content to the website www.xzthjc.com consultation.