The environmental molded case circuit breaker is mainly used to distribute electric energy and protect the circuit and power equipment from overload, short circuit, under voltage and other faults. Equipment maintenance procedures are the requirements and regulations for daily maintenance of equipment. It can extend the service life of equipment and ensure safe and comfortable work by adhering to the equipment maintenance regulations. The main contents of the project shall include:

（1）須嚴格按說明書規定安裝塑殼斷路器；

(1) The molded case circuit breaker shall be installed strictly according to the specification;

ABB塑殼斷路器代理

（1）安裝前要對銘牌上的參數與實際需要是否相符，將斷路器垂直固定在安裝板上。

(1) Before installation, check whether the parameters on the nameplate are consistent with the actual needs, and fix the circuit breaker on the installation plate vertically.

（2）斷路器在投運前，要仔細檢查固定連接部分是否牢固，并保證操作機構處于靈活狀態。

(2) Before the circuit breaker is put into operation, it is necessary to carefully check whether the fixed connection part is firm, and ensure that the operating mechanism is in a flexible state.

（3）斷路器出廠時已確定準確，使用中可隨意調節。線路發生過載或短路故障斷路器動作后，應先排除故障，再進行合閘操作。

(3) The circuit breaker has been determined accurately when leaving the factory and can be adjusted at will during use. In case of overload or short-circuit fault, the circuit breaker shall remove the fault before closing.

（4）斷路器在使用期間應進行周期性檢查，要定期對傳動部分加潤滑油，同時清 除外殼灰塵，消 除滅弧室內壁和側片上的金屬顆粒及黑煙灰。

(4) The circuit breaker shall be inspected periodically during use. The transmission part shall be lubricated regularly. Meanwhile, the dust of the shell shall be removed, and the metal particles and black soot on the wall and side pieces of the arc extinguishing chamber shall be eliminated.

（5）塑殼斷路器在日常維護保養中，不許拆卸零部件，發現異常立即停車，不允許帶病運轉；

(5) During daily maintenance, plastic case circuit breaker shall not be disassembled, and stop immediately if abnormal, and operation with defects is not allowed;

（6）非工作時間應加護罩，長時間停歇，應定期進行擦拭，潤滑、空運轉；

(6) The shield should be added during non working hours, and it should be wiped, lubricated and idled regularly when it stops for a long time;

（7）附件和專用工具應有專用柜架擱置，保持清潔，防止研傷，不得外借。

(7) Accessories and special tools shall be set aside with special cabinet frame, keep clean, prevent research injury and shall not be borrowed.

塑殼斷路器的日常維護保養是設備維護的基礎工作，必 須做到制度化和規范化。對設備的定期維護保養工作要制定工作定額和物資消耗定額，并按定額進行考核，塑殼斷路器定期維護保養工作應納入車間承包責任制的考核內容。

The daily maintenance of MCCB is the basic work of equipment maintenance, which must be institutionalized and standardized. The regular maintenance of equipment shall be determined with work quota and material consumption quota, and assessed according to the quota. Regular maintenance of molded case circuit breaker shall be included in the assessment content of workshop contract responsibility system.